翻訳と辞書
Words near each other
・ Brine (food)
・ Brine (hydrology)
・ Brine (refrigerant)
・ Brine (surname)
・ Brine Lacrosse
・ Brine lake
・ Brine Leas School
・ Brine pipeline
・ Brine pool
・ Brine rejection
・ Brine shrimp
・ Brine spring
・ Brined cheese
・ Brinegar Cabin
・ Brinegar v. United States
Brinell scale
・ Brinelling
・ Brineton
・ Brinevskoye mine
・ Bring
・ Bring 'Em All In
・ Bring 'Em Bach Alive!
・ Bring 'Em Back Alive
・ Bring 'Em Back Alive (book)
・ Bring 'Em Back Alive (film)
・ Bring 'Em Back Alive (TV series)
・ Bring 'Em Down
・ Bring 'Em In
・ Bring 'Em In (Buddy Guy album)
・ Bring 'Em In (Mando Diao album)


Dictionary Lists
翻訳と辞書 辞書検索 [ 開発暫定版 ]
スポンサード リンク

Brinell scale : ウィキペディア英語版
Brinell scale

The Brinell scale characterizes the indentation hardness of materials through the scale of penetration of an indenter, loaded on a material test-piece. It is one of several definitions of hardness in materials science.
Proposed by Swedish engineer Johan August Brinell in 1900, it was the first widely used and standardised hardness test in engineering and metallurgy. The large size of indentation and possible damage to test-piece limits its usefulness.
The typical test uses a diameter steel ball as an indenter with a force. For softer materials, a smaller force is used; for harder materials, a tungsten carbide ball is substituted for the steel ball. The indentation is measured and hardness calculated as:
:\operatorname=\frac
where:
:''F'' = applied force (kgf)
:''D'' = diameter of indenter (mm)
:''d'' = diameter of indentation (mm)
Brinell hardness is sometimes quoted in megapascals, the Brinell hardness number is multiplied by the acceleration due to gravity, 9.80665 m/s2, to convert it to megapascals.
The BHN can be converted into the ultimate tensile strength (UTS), although the relationship is dependent on the material, and therefore determined empirically. The relationship is based on Meyer's index (n) from Meyer's law. If Meyer's index is less than 2.2 then the ratio of UTS to BHN is 0.36. If Meyer's index is greater than 2.2, then the ratio increases.〔Tabor, p. 17.〕
''BHN'' is designated by the most commonly used test standards (ASTM E10-14〔ASTM E10 – 14 Standard Test Method for Brinell Hardness of Metallic Materials〕 and ISO 6506–1:2005〔ISO 6506–1:2005 Metallic materials – Brinell hardness test – Part 1: Test method〕) as ''HBW'' (''H'' from hardness, ''B'' from brinell and ''W'' from the material of the indenter, tungsten (wolfram) carbide). In former standards HB or HBS were used to refer to measurements made with steel indenters.
HBW is calculated in both standards using the SI units as
:\operatorname=0.102 \frac
where:
:''F'' = applied force (N)
:''D'' = diameter of indenter (mm)
:''d'' = diameter of indentation (mm)
== Common values ==
When quoting a Brinell hardness number (BHN or more commonly HB), the conditions of the test used to obtain the number must be specified. The standard format for specifying tests can be seen in the example "HBW 10/3000". "HBW" means that a tungsten carbide (from the chemical symbol for tungsten or from the Swedish/German name for tungsten, "Wolfram") ball indenter was used, as opposed to "HBS", which means a hardened steel ball. The "10" is the ball diameter in millimeters. The "3000" is the force in kilograms force.
The hardness may also be shown as XXX HB YY''D''2. The XXX is the force to apply (in kgf) on a material of type YY (5 for aluminum alloys, 10 for copper alloys, 30 for steels). Thus a typical steel hardness could be written: 250 HB 30''D''2. It could be a maximum or a minimum.

抄文引用元・出典: フリー百科事典『 ウィキペディア(Wikipedia)
ウィキペディアで「Brinell scale」の詳細全文を読む



スポンサード リンク
翻訳と辞書 : 翻訳のためのインターネットリソース

Copyright(C) kotoba.ne.jp 1997-2016. All Rights Reserved.